Quilt-as-you-go, Serger Quilt: tutorial Part 2: BORDERS

Last week we started a baby quilt by serger.  I hope some of you are sewing this along with me and will send me pictures of your completed project.

Part 1 ended here:

Fabric Preparation for Borders

Cut the following from Border 1 fabric AND from batting:

2 – 2 ½” x 30”*

2 – 2 ½” x 38”*

*Cut borders 2” longer than length needed.

Let’s put these borders on, shall we?

The reason I suggested you cut your borders 2″ longer than the length needed is to give you a little wiggle room at each end.  As we practice quilt-as-you-go by serger, I find that sometimes my fabric shifts at the beginning of my seam.  I have gotten to where this rarely happens any more, but this extra length will help alleviate that, if you find it happens to you.

CUT BACKING STRIPS:

I just realized I forgot to tell you to cut your backing strips as well, so now go ahead and cut 4 backing strips to match your border 1 and batting strips.  These backing strips might match the backing for the central square, but that is not necessary.  This is a perfect opportunity to have a pretty pieced backing.

The order of the borders, based on the measurements I gave above, is to serge the top and bottom borders first, followed by the side borders.

For serger quilt-as-you-go, you will layer your fabric from the table up as follows, with top raw edges matching:

Backing strip: RIGHT side UP   (green in picture)

Quilt sandwich: RIGHT side UP   (pieced in picture)

Border fabric: WRONG side UP    (orange in picture)

Batting: on top.

border arrangement

The raw edges are not aligned in this picture, but you want to align them.

Start your border strips about 1″ before the central square.  Pin all layers together carefully.

*Pinning Recommendation:  I use LONG quilting pins when I serge.  I will often pin parallel to the edge, which keeps my pins out of my knife, but if I pin perpendicular to  the edge I place my pins so they hang off the edge of the fabric about an inch.  That way they are both easy to see and easy to remove.  NEVER serge over a pin.  I have only had to replace my knife once in 12 years, and that was after serging over 1 pin.  That is all it takes.

**If  you find your fabric edges slip and slide around despite pinning, use glue in the seam allowances to hold them together.  I use glue stick or Elmer’s blue gel a lot, especially when serging.  If the glue does not dry fast enough, iron the two fabric layers together as you glue and it will dry quickly.

Serger Setting for SERGING SEAMS:

4 Thread Overlock
Stitch Width: Widest Setting
Stitch Length: 3 mm

Serge the long seam trimming off an even amount.

Flip the border pieces out from the center and press on both sides.  Press to flatten seam as much as possible, pulling on the fabric against the seam to be sure it was caught in the stitching everywhere.

flip borders out 1

flip borders out 2

Change serger stitch or cutting width to narrowest width and serge baste the long edge, without trimming, to hold the 3 layers (backing, batting, and border) together.  * As you serge, continue to smooth the fabric out from the seam to be sure the raw edges meet and all layers are caught in the basting.

Return stitch or cutting width back to widest setting.

Repeat for opposite border.

You can cut off the 1″ of border that hangs off each end with a rotary cutter to square up the center, or cut it off when serging the side borders.

Arrange the fabrics the same way as explained above for the side borders, serge, press, and baste outer edge.

BORDER 2

Cut border 2 fabric, batting, and backing strips as follows:

2 – 4″ x 32″

2 – 4″ x 42″

Repeat the same procedure with the first borders.  When you are finished your outer edge should be completely squared up, basted and ready for binding.  If your quilt needs additional squaring up, it is fine to trim away some of the serger basting.  If you trim away all of the stitching in an area, rebaste that section without trimming on the serger to hold the layers together.

BINDING Prep:

Coming up in the last installment of this series will be adding a straight grain binding with a faux serger piping.

1/2 yard binding fabric.

Cut 5 strips 2 1/2″ x WOF (Width of fabric).

Thread: at least 2 spools of 40 wt. polyester or rayon embroidery thread, or 1 spool of a 12 weight decorative thread like Sulky Blendables, Jean Stitch, or Pearl Crown Rayon.

Part 3 Binding here.

Until next time,

Sherilyn

Advertisements

2 Comments (+add yours?)

  1. Trackback: Binding: Serger Quilt part III (finally) | Cherished Needle Creations
  2. Trackback: Quilt-as-you-go, Serger Quilt: tutorial | Cherished Needle Creations

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Materia Medica

by Chloe Sobejko

Plant Therapy Blog

A creative home for machine embroidery, sewing, and serger projects and techniques.

Keirsten's Kitchen

It's Paleo... ish

Notorious Beauty Blog

I believe in manicures. I believe in primping at leisure and wearing lipstick. I believe happy girls are the prettiest girls. -Audrey Hepburn

Cat Eyes Red Lips

Beauty, Fashion, Lifestyle

theimaginationmuscle

Birthplace to all ideas:please, let me share a few of my own.

adoptingjames

Read our Mission. Find out how you can help us adopt James.

Dresses & Me

I love to sew

knit the hell out

More obsessed with each passing stitch.

M&J Blog

A creative home for machine embroidery, sewing, and serger projects and techniques.

Blumenkinder Heirlooms

Gracious Living by the Yard

The Seeds of 3

Sewing, Gardening, and Homeschooling Adventures

Sewnhenge

Sewing Quilting Living Loving

WeAreDAR

To Give. Globally.

dianedziel

fashion design is also pattern making and sewing

%d bloggers like this: